At times, the Bush TV remote may not be working even with new batteries. This is common for most TV remotes, and Bush is no exception. The other remote issues can be rectified easily unless the remote has a physical defect and hardware malfunction. This guide explains the troubleshooting methods in detail.
Before learning the fixes, you should know the primary causes that affect the Bush TV remote’s functionality. Once you identify the core reason, you can fix it rapidly.
| Causes | Reasons | Solutions |
|---|---|---|
| The remote signals getting interrupted | Presence of blocking objects | Ensure no objects are obstructing remote signals |
| Bush TV remote responds after multiple clicks | Residual power in the remote | Reset the Bush TV remote |
| Certain buttons on the remote don’t work | Batteries are drained or weak | Replace the remote batteries |
| Bush TV fails to receive commands | Glitches in the Bush TV | Power cycle the Bush TV |
| The remote fails to pair with the Bush TV | Outdated Bush TV firmware | Update the Bush TV software |
| Remote completely dysfunctional | Damage to the remote’s components | Repair the Bush TV remote |
Use the Bush TV Remote in a Short Range
The primary factor for seamless TV control is using the remote within the Bush TV range. You can check the exact remote working range from the remote manual. If you can’t find those details in the manual, try operating the remote at a distance of fewer than 30 feet from the Bush TV. Then, press the volume button and check whether your TV’s volume increases or decreases. If not, move to the next fix.
Clear the Obstructions
If the Bush remote fails to control the TV at close range, check if any objects are blocking the sensor. If so, they may block the remote signals from reaching the TV sensor. Also, be sure that there are no IR-emitting objects near your Bush TV. If found, relocate them from the remote signal path. Now, check if the Bush TV works. If the issue persists, the next troubleshooting method can fix the problem.
Power Cycle the Bush TV
Sometimes, Bush TV may not be able to receive the remote signals. This may happen due to voltage fluctuations on your Bush TV. To remove that and make the TV remote functional, power cycle the Bush TV.
- Press the TV Power button to turn off the Bush TV.
- Remove the TV power cord from the electric source.
- Wait for a few minutes to let the residual power discharge.
- Plug the TV cord back into the electric source.
- Click the TV Power button to turn on the Bush TV.
Once turned, verify whether the Bush TV remote works fine.
Clean the Bush TV Remote
If the Bush TV remote is not working after power cycling the TV, you must clean the remote. The floating particles may cover the remote’s IR sensor, resulting in unresponsiveness. So, pick a soft microfiber cloth and gently wipe the dust on the remote’s IR sensor.
Also, clean the remote button gaps using a cloth dipped in an Isopropyl Alcohol solution. Disassemble the remote and check if the buttons can go inside while pressing them. If it doesn’t work after cleaning, try the next fix.
Replace the Bush Remote Batteries
The batteries on your Bush TV remote may last only for a few months. After that, you should replace them. Using drained batteries can affect the remote’s proper functionality. So, open the remote’s battery compartment, eject the old batteries, and replace them with new 2 AAA batteries. Once the batteries are inserted properly, check whether the remote works well.
Re-pair the Bush TV Remote
Sometimes, the remote may accidentally be unpaired from the Bush TV. However, re-pairing the remote will make it work again.
- Pair Bush Android TV remote – Turn on the Bush TV → Long-press the Home and Left buttons for 5 seconds when the pairing prompt appears→ Select the Remote → Press the OK button.
- Pair Bush Fire TV remote – Click the Power button → Long-press the Home button → Release when the remote’s light flashes.
Still, the Bush TV remote is dysfunctional? Try the next method.
Update the Bush TV Firmware
If you can’t pair the Bush TV remote, the TV’s firmware needs to be updated. You can update the Bush TV firmware using the below steps according to its operating system. Since you need to access the TV settings, you should connect a mouse or wireless keyboard with a touchpad to your Bush TV to use as a remote control.
- Bush Fire TV: Tap the Settings icon → Select My Fire TV → Choose About → Click Check for System Update → If an update is available, you will be asked to download and install it.
- Bush TiVo TV: Go to Settings → Select Setup → Click More → Select Software Upgrade → Tap Scan for upgrade → Your TiVo TV will search for the newest software and install it if available.
Reset the Bush TV Remote
In some cases, the Bush TV remote may not be working because of a flea power. It happens when you keep the Bush TV remote unused for a longer period. In this case, resetting is the only solution to restore it to its defaults.
- Reset Bush Android TV remote – Power off the Bush TV and remote the TV cord from the electric source → Plug the TV cord into the electric socket after a minute → Long press the TV Power button.
- Reset Bush Fire TV remote – Turn off the TV and remove its cable → After a minute, hold the Left, Menu, and Back buttons together for 12 seconds → Wait for 5 seconds → Remove the batteries from the remote.
Thus the remote resetting is successful. Now, pair the remote with the Bush TV and check whether the problem has been fixed.
Inspect the Bush TV Remote’s IR Emitter
If the Bush TV remote sensor is not working, inspect the remote’s component, the IR emitter. To do this, open your phone camera and show your Bush TV remote facing the rear camera lens. Press the Power button, and you should see a light on the screen. If you can’t see a flashlight, the remote’s IR is damaged. This means that the IR emitter has become faulty, and it is better to repair it or buy a new remote.
Contact Bush TV Customer Support
If you think of repairing the remote or claiming a replacement remote, contact the nearest Bush TV service center. The skilled technicians will inspect your remote, fix the remote issue, and bring it back to working condition. If your remote is covered under warranty, you can claim a free service or replacement. For more information, visit its official website to know the possible ways to reach them.
Try These Remote Alternatives
If you have submitted the remote for repair or ordered a replacement remote, use the following alternatives to control the Bush TV.
- Use TV Buttons – Most Bush TVs have physical buttons, such as Power, Channel, Volume, Menu, and Input. These buttons allow you to manage the Bush TV functions.
- Use the Remote App – Bush TV runs on Android TV and Fire OS. To control Bush Android TV, install the Google TV app on your Android (Play Store) or iPhone (App Store) and use it. For Bush Fire TV, you can use the Amazon Fire TV app as a remote. You can get that app from the Play Store or App Store. These apps can work only if your phone and TV are on the same WiFi network.
FAQ
Yes, use the IR remote app on your Android phone to control your Bush TV.
