Are you keeping a separate remote to control your Logik TV and set-top box? If so, it is time to use your set-top box controller as a universal remote to control your Logik TV. However, to configure a universal remote, you must know the remote codes assigned to your Logik TV. In this guide, we have tabulated the Logik TV remote codes for top universal remote brands with steps to set up a universal remote.
List of Universal Remote Codes for Logik TV
The universal remote codes for Logik TV will be in 3, 4, or 5 digits, based on the remote brand you use.
| Universal Remote Brands | Remote Codes |
|---|---|
| Comcast | 4 Digit: 0016 5 Digit: 10016, 12246, 12293 |
| DirecTV | 10016, 12293 |
| Dish | 518, 675, 031 |
| GE | 3 Digit: 001, 083, 031, 000 4 Digit: 5003, 5020, 5040, 5041, 5046, 0031, 0000, 0001, 1661, 1421, 1691, 3421 |
| One For All | 3 Digit: 016, 165, 180 4 Digit: 0698, 3719, 1865, 4226, 0264, 1795, 1585, 1037, 3432, 3831, 3802, 0706, 3005, 2486, 1687, 1217, 0016, 2530, 1645, 2241, 2095, 2371, 0037, 4340, 4218, 0773, 0009, 3505, 2673, 2457, 3030, 0371, 1702, 0880, 5201, 3428, 1667, 1626 |
| Philips | 3 Digit: 028, 043 4 Digit: 1064, 0036, 0207, 0256, 0263, 1661, 1421, 1691, 3421, 0038, 0704, 0601, 0701 5 Digit: 16440, 11549, 10644, 10242, 16630, 17921, 16263, 15162, 15934, 16032, 13523, 12501, 16940, 17048, 14216, 16611, 15320, 15526, 18029, 14235, 16915 |
| RCA | 3 Digit: 001, 083 4 Digit: 1865, 1217, 1001, 1083, 1006  5 Digit: 11217, 11865, 12293 |
| Spectrum | 3 Digit: 072, 211, 213 4 Digit: 0101, 1301, 1581, 0021, 0301, 1217, 1865, 0031, 0001, 1001 5 Digit: 11217, 11865 |
| U-Verse | 0031, 0000, 0001, 1001, 1293 |
Program Universal Remote to Logik TV With Codes
Using the remote codes mentioned above, you can easily program a universal remote with your Logik TV. The steps to program most universal remotes are almost the same. Before you proceed to program the remote, your universal remote should be loaded with batteries, and your Logik TV should be turned on.
Manual Code Entry
1. Pick your universal remote and point it towards your Logik TV sensor.
2. Long press the Device button on the remote. Since you are programming to control a Logik TV, press the TV button on your remote. In some universal remotes, you need to press the Setup button before pressing the TV button.
3. Once you press the TV button, the LED light on the remote glows.
4. While holding the TV button, refer to the remote codes table and enter the code for your TV brand. The LED light on the remote turns off.
5. Release the TV button once the LED light on the remote glows up again. This indicates that you have entered the correct remote code.
6. Confirm whether the remote is paired with the Logik TV by pressing the Power or Volume button. If your Logik TV doesn’t respond, repeat the whole process using the next code.
Automatic Code Search
1. Point your universal remote towards your Logik TV and press the TV button.
2. Then, press the Power button and TV button simultaneously for a few seconds until the LED light on your remote turns off and on.
3. Locate the Play button on your universal remote. Press & release the Play button and wait for a few seconds. If your Logik TV turns off, it means that the remote found the code of your TV.
4. If your Logik TV doesn’t turn off, repeat the process once again. Your remote will search for a new set of codes to pair with your Logik TV.
5. Once your TV turns off, press the Reverse/Rewind button to turn your TV back on.
Note: If your TV does not turn on, you need to repeat the whole process once again.
6. Once your universal remote’s LED turns off and the Logik TV turns on, press the Stop or OK key to save the code.
Program Universal Remote to Logik TV Without Code
When you can’t find the code for your remote brand or if it takes time to find the correct code, you can try this method.
1. Press and hold the TV button and OK/Select button on your universal remote for 5 seconds.
2. The LED light will blink on the TV button of your universal remote.
3. Then, simultaneously press and hold the Channel Up and Channel Down buttons for a few seconds.
4. Now, press the Up or Down button on your remote continuously for one-second intervals until your TV turns off.
The universal remote is successfully programmed with your Logik TV when your TV turns off. You can turn it on using the Power button and control your Logik TV.
Note: The below instructions may not be suitable for some universal remotes. If you can’t program your remote using our steps, read the user manual provided by the remote manufacturer.
FAQ
You can program your Sky universal remote to a Logik TV using remote codes such as 3460, 3859, 3033, or 3830. For complete instructions on setting up a remote, you can refer to this website.
